Your specialist in diesel technology
No vehicle selected Select make, model and engine

Loading...
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

S
Selected vehicle
Show matching parts
Vehicle search Select make, model and engine
Loading...
  1. 1 Make
  2. 2 Model
  3. 3 Engine / type
F
Select engine / type

Enter a UK registration number to find matching vehicles from our shop inventory.

P0087: fuel rail pressure too low – causes, diagnosis and fixes (incl. P0088)

DieselFix Neuss |

The engine cranks for a long time before it starts, lacks power or even stalls – and the fault memory shows P0087. The engine control unit reports that not enough pressure is being built up in the common rail. The cause is often on the low-pressure side or an injector that sends too much fuel back to the return line.

What does P0087 mean?

P0087 – Fuel rail/system pressure too low
The pressure measured by the rail pressure sensor is clearly below the target that the engine control unit sets for the current operating condition.

Note: the meaning is defined by the OBD-II standard; some manufacturers add their own sub-codes. Always read the complete fault memory including the freeze-frame data.

Typical symptoms

  • Long cranking before the engine starts, often especially when warm
  • Loss of power or limp mode
  • Jerking when accelerating
  • The engine stalls while driving or at idle
  • Engine warning light

The most common causes

CauseHow to check itNote
Clogged fuel filter or air in the fuel systemReplace the filter, bleed the system, look for air bubbles in the linesCommon after a filter change
Weak low-pressure supply (electric fuel pump, gear pump)Measure the supply pressure or flow rateAlso check tank venting and fuel lines
Sticking or dirty fuel metering valve on the high-pressure pumpCheck activation and resistance, watch live dataIf there are metal particles in the fuel, find the cause
Excessive leak-off from one or more injectorsLeak-off test of the injectorsOne leaking injector makes rail pressure collapse
Leaking pressure control valve on the rail or pumpCheck the return flow at the valve, activate it
Worn high-pressure pumpOnly after ruling out the other causes; check the fuel for metal particlesParticles travel into the injectors
Rail pressure sensor or wiringWith the engine off, the sensor must read about 0 bar; check the connector

Step-by-step diagnosis

  1. Read the fault memory and note whether P0087 occurs when starting, at idle or under load.
  2. Compare target and actual rail pressure in live data – while cranking and when accelerating.
  3. Check the low-pressure side: fuel filter, bleeding, supply pressure. More on the filter: Diesel fuel filter.
  4. Carry out a leak-off test on the injectors: an injector with clearly more return flow than the others is suspicious.
  5. Check the fuel metering valve, pressure control valve and rail pressure sensor.
  6. Only then assess the high-pressure pump.

P0088: fuel rail pressure too high

The opposite case, P0088 ("fuel rail/system pressure too high"), occurs when the pressure is above target. Typical causes are a sticking pressure control valve, a stuck fuel metering valve, a rail pressure sensor reading incorrectly or a kinked or blocked return line. Here too, diagnosis starts by comparing target and actual rail pressure.

Can I keep driving with P0087?

This is not recommended: if rail pressure drops further, the engine can stall while driving. Only drive to the nearest garage and avoid high loads.

If an injector is the cause

If the leak-off test reveals a faulty injector, replacement is the reliable fix. Remanufactured and new injectors by vehicle: Injectors. How to test injectors: Testing a diesel injector. On many engines the new injector must then be coded.

Frequently asked questions

Can a faulty injector cause P0087?

Yes. If an injector has excessive leak-off, pressure escapes from the rail. The pump can then no longer hold the target, especially when starting and with a warm engine.

P0087 right after a filter change – why?

Usually air in the system, or a wrong or poorly sealed filter. The system must be bled correctly after the change.

Why does P0087 mainly appear with a warm engine?

Warm diesel is thinner. Internal leaks in injectors or in the high-pressure pump then have a bigger effect.

What is the difference between P0087 and P0088?

P0087 means pressure too low, P0088 pressure too high. With P0088 the cause is usually the pressure control or the sensor.

Leave a comment

Please note: comments must be approved before they are published.

Delivery country

Prices and refundable deposits depend on the delivery country. Your language selection stays unchanged.