The engine shakes at idle, knocks on one cylinder or runs rough when cold – and the fault memory shows P0263, P0266, P0269 or P0272. The engine control unit is reporting that one specific cylinder does not contribute to engine torque the way the others do. The last digit tells you which cylinder – and very often that cylinder's injector is behind it, but not always.
What do P0263, P0266, P0269 and P0272 mean?
Using crankshaft speed fluctuations, the control unit detects that one cylinder delivers clearly more or less torque than the others. The smooth-running control has reached its quantity correction limit for that cylinder.
For cylinders 5 and 6 the matching codes are P0275 and P0278. There are also circuit codes such as P0261/P0262 (cylinder 1) or P0264/P0265 (cylinder 2) for "injector circuit low/high" – they point to an electrical problem, not to an uneven cylinder contribution.
Note: the meaning is defined by the OBD-II standard; some manufacturers add their own sub-codes. Always read the complete fault memory including the freeze-frame data.
Typical symptoms
- Rough idle, noticeable vibration through the steering wheel or body
- Knocking or rattling from a single cylinder
- Smoke when starting or accelerating
- Loss of power, possibly limp mode
- Engine warning light, sometimes only when cold
The most common causes
| Cause | How to check it | Note |
|---|---|---|
| Missing or wrong injector coding (IMA/IQA/C2I) after a replacement | Compare the code stored in the ECU with the one on the injector: injector coding | Most common cause right after a repair |
| Excessive leak-off or worn nozzle | Leak-off test, compare all injectors | A dribbling nozzle raises the contribution, a coked one lowers it |
| Leaking injector seal (copper washer), combustion leak, carbon in the injector well | Look for a blow-by noise, soot and deposits around the injector. More: seals and O-rings | Always fit new seals whenever an injector is removed |
| Low compression (valves, piston rings) | Compression or relative compression test | A new injector will not fix this |
| Faulty glow plug | Test the glow plug if the fault only appears on a cold start | Usually fine once the engine is warm |
| Air in the fuel | Bleed the fuel system, check lines and filter for leaks | Often after a filter change or running the tank dry |
| Faulty injector (quantity, spray pattern, control valve) | Only after ruling out the other causes; bench test | Typical sign: one single cylinder outside the tolerance band |
Step-by-step diagnosis
- Read the complete fault memory and note whether the code sets cold, warm, at idle or under load.
- In live data, read the smooth-running or quantity correction values of every cylinder at warm idle. A single cylinder clearly outside the tolerance band is the prime suspect.
- Check the injector coding and re-enter it if needed: injector coding and idle problems.
- Carry out a leak-off test and compare the injectors with each other.
- Compare compression across all cylinders to rule out a mechanical cause.
- Cross-check: swap the suspect injector with one from another cylinder (update the coding!). If the deviation follows the injector, the injector is at fault; if it stays, the cause is in the cylinder.
Can I keep driving with P0263–P0272?
Short trips are usually possible if the engine still runs reasonably smoothly, but do not wait long: a dribbling injector can damage the piston, and a leaking seal can erode the injector well. With heavy smoke or a fuel smell, only drive to the workshop.
If the injector is the cause
If the measurements and the swap test point to one injector, replacement is the reliable fix. Remanufactured and new injectors by vehicle: Injectors. Further help: testing a diesel injector and diesel vibrating at idle. Remember new seals and coding the new injector.
Frequently asked questions
Which cylinder do P0263, P0266, P0269 and P0272 refer to?
P0263 is cylinder 1, P0266 cylinder 2, P0269 cylinder 3 and P0272 cylinder 4. The manufacturer defines which cylinder is number 1.
The code appeared right after an injector replacement – why?
Usually the new injector was not coded or was coded incorrectly. An old, reused copper washer can also play a part.
Does P0263 always mean a faulty injector?
No. Low compression, a combustion leak, a glow plug or air in the fuel can also cause an uneven cylinder contribution. The swap test gives a clear answer.